Home > Products > Exit Button Switch > Electric Gate Garage Door Home.....
Electric Gate Garage Door Home Door Wireless Remote ControllerElectric Gate Garage Door Home Door Wireless Remote ControllerElectric Gate Garage Door Home Door Wireless Remote ControllerElectric Gate Garage Door Home Door Wireless Remote Controller

Electric Gate Garage Door Home Door Wireless Remote Controller

  • Model: DH-K809
  • Working Voltage: DC12V
  • RF Frequency: 315mhz or 433MHZ
  • Channel: 1 Channel
  • RF Working mode:Super heterodyne receiver
  • Battery: 27A/12V Alkaline Remote Battery.
  • Remote Control Distance: >30 meter(In open environment)
  • Support remote control type: Fixed code, learning code
  • Output: Normally open, Common, Normally closed
  • Usage: Motorcycle alarm system, car alarm system, auto gate, door motor or other security product.

DH-K809 is a remote control with elegant outlook and high frequency stability. The outer case is made of excellent imported ABS flame retardant material. The outer metal ring can prevent damaged by knock against. The ABS panel and buttons are designed for excellent texture. With the mobile cover, it can avoid the mis-trigger which makes this remote control is more safe and reliable. It adapts surface acoustic wave resonator and high-power radio frequency circuit. The advantage of the circuit is: it only consumes currents when pressing the button. no current consumption ordinary time so its very user friendly.


Working/output way:
1.Jog/Non-Latched: Press one button is Working /ON. Loosen your finger on the same button is Stop/OFF. One channel switch need one buttons remote control.
2.Self -lock/Self-Latched: Press one button for one time is working/ON. Press the same button again is stop/OFF. One channel switch need one buttons remote control.
3.Inter-lock /Latched: Press one button is working/ON, press another button is stop/OFF. One channel switch need 2 buttons remote control.
4.Delay: Press remote control relay pull-in, release the remote control and begin timekeeping, after 5s,10s,15s will automatically close the relay


Specification:
1.Input Voltage: DC10-14V
2.Standby Current: <5MA
3.RF Frequency: 315MHz or 433MHZ
4.RF Working mode: Super heterodyne receiver
5.Receiver Sensitivity: >90dBm
6.Remote Control Distance: >100 meter(In open environment)
7.Decoding Way: MCU Software decoding
8.Can store the number of remote control:50
9.Support remote control type: Fixed code, learning code
10.Channel: 1CH
11.Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched, Delay off)
12.Wiring Method: Fixed wiring terminal
13.Working Voltage: DC12V
14.Output Current: 10A
15.Rated load:10A 250VAC / 10A 125VAC
10A 30VDC / 10A 28VDC
16.Output:Normally open, Common, Normally closed
17.Dimension:3.5cm*3cm*1.6cm


Application: Remote gate controls, Brake; Remote keyless entry (RKE); Wireless control Curtain device; Wireless security systems; Wireless Industrial Control; Wireless parking lot barrier


Description:
1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
4.Delay: Press remote control relay pull-in, release the remote control and begin timekeeping, after 5s,10s,15s will automatically close the relay


Shenzhen UDOHOW Electronics Co., Limited

Tel:+86 13612936220

Contact Person:Yimo Yang

Send your inquiry directly to us
show code on cursor in the input box
( 0 / 3000 )